Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - boomtheroom

Pages: [1]
1
Sherco Tech / question for top end rebuilders
« on: January 15, 2020, 11:23:18 PM »
just looking at the cylinder and notices a small hole right at the top of the exhaust port .. is it supposed to be there? a friend who has a 2017 ser-300 ours id a 2014 ser-300 has the exact same hole in the same place!!! anyone enlighten me ??
Cheers!

2
Sherco Tech / squish
« on: January 14, 2020, 12:46:52 AM »
anyone know what squish should be for a 2014 ser-300?

3
Sherco Tech / Re: top end rebuild 2014 300ser
« on: January 08, 2020, 03:11:19 AM »
used the one that cam n the B piston rebuild kit

4
Sherco Tech / top end rebuild 2014 300ser
« on: January 05, 2020, 02:36:25 PM »
Just after a we bit of advise

just did a top end rebuild on the sherco

but it sounds and runs like crap especially low end..

new plug, rings, pistons and gaskets..nothing else touched

what u think?

https://www.youtube.com/watch?v=s9y1njZhLVU&fbclid=IwAR2-4qjXCQgLXEcttdVb8Vt6KiVvvhpXZGCG-xRRNSs9MOJLiM5OmDdk5eE


5
General Discussion / ser300
« on: December 12, 2019, 08:07:08 PM »
Hi All

Any one willing to take some photos of the wiring and fuel line routing under the tank of their ser300?
my wife did a piston rebuild but forgot to take pictures of the routing and is worried that they might be wrong when she puts the fuel tank back in place... Cheers!

6
Sherco Tech / 2014 Se-r levers
« on: August 17, 2018, 04:17:50 PM »
wanting to replace my clutch and brake  levers
anyone know what year and model ktm ones are interchangeable with the sherco?

7
Sherco Tech / Re: 2014 300ser rubbing
« on: July 30, 2018, 09:35:40 AM »
the right side with a slight inward bend... is that normal? .. if so ill just bend the left to match the contour..

8
Sherco Tech / Re: 2014 300ser rubbing
« on: July 30, 2018, 01:09:39 AM »
No one know?

9
Sherco Tech / Re: 2014 300ser rubbing
« on: July 28, 2018, 09:53:20 PM »
here

10
Sherco Tech / Re: 2014 300ser rubbing
« on: July 28, 2018, 09:52:48 PM »
Also is this bend in the rear normal?

11
Sherco Tech / Re: 2014 300ser rubbing
« on: July 28, 2018, 09:50:13 PM »
Mine almost looks like its resting on it but no marks

can u post pics?

12
Sherco Tech / Re: 2014 300ser rubbing
« on: July 28, 2018, 12:47:51 PM »
Anyone with a ser300 can post me a picture of their carb and how it sits on their bike please? 2013-2015

13
Sherco Tech / 2014 300ser rubbing
« on: July 28, 2018, 04:11:03 AM »
i just got myself a ser300 only problem is the carb is sitting on the crankcase ..the bottom nut on the carb is actually touching it..and boring a hole into the crank case..i can figure out why..as this is the only way it sits. any ideas?

Pages: [1]