Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - czguy

Pages: [1] 2 3 ... 5
News / Re: CMI Canada is the new Sherco distributor in Canada
« on: July 23, 2021, 05:51:11 PM »
Scott,  I picked up a 2017 300, use my 2016 for parts, many parts fit, rads, engine cases, steering, wheels, starter, swing arm suspension etc. Only plastic doesn't fit,. Craig is a bit to deal with, robbie is great. Not stocking parts is just great way to run things,that'swhat guy said. I would go back to husky I think,

News / Re: CMI Canada is the new Sherco distributor in Canada
« on: June 01, 2021, 02:48:10 PM »
Just charming,  anyone even  thinking of getting a sherco, run away, don't walk, . Crazy getting 2 small parts, a spring and a gasket,. No problem taking my money when buying 2 new bikes,  but come time for  parts, good luck,  phone calls,  Facebook,  emails,  no parts in stocks in Canada.  That is the response...

Sherco Tech / Gasket
« on: May 30, 2021, 07:46:30 AM »
fixing the  return shifter spring on my ser300, a bit of a pain,  but I need the gasket that goes around the case, in canada parts are tough to get, my question is will gasket maker work. Not worried about sealing,  my concerns is clearance.  Is the thickness of original gasket critical to any clearance for water pump or shifter shifter length.  I am sure I am not the only person that came across this.  Normally I am a oem parts guy,

News / Re: CMI Canada is the new Sherco distributor in Canada
« on: January 17, 2020, 01:18:04 PM »
Reminds me of the CZ back in late 70,s.. soon buying old bikes to rob parts to keep them going..

News / Re: CMI Canada is the new Sherco distributor in Canada
« on: January 16, 2020, 03:53:44 PM »
I was there on weekend.  Getting a few new parts . So far not too impressed.

General Discussion / Re: Bendix washer
« on: January 12, 2020, 06:32:34 PM »
They only come with a new bendix. Buy a bendix.  In Canada they can be tough to get.

General Discussion / Re: Bendix washer
« on: January 11, 2020, 01:21:12 PM »
15.92 mm od  8.0mm id .21mm thick.. just measured new one.

Sherco Tech / Re: battery question
« on: September 07, 2019, 08:59:01 AM »
I put in the standard battery. ck voltage about mid rev. 14.8 volt 14.7 with headlight on. not a big difference. on idle about 14.6 volt. 14.8 volt should not hurt battery.

Sherco Tech / battery question
« on: August 25, 2019, 02:32:24 PM »
I  need a battery for 2016 ser 300. I keep hearing talk about earth x and lithium over stock, but up here we get some cold. anyone have any issue in below 0 c . Any model numbers of battery. must be reliable. Which one is best

Classifieds / Re: 2016 sef Factory 300
« on: July 05, 2019, 03:51:10 PM »
ok . I will ask how much

General Discussion / Re: Bendix change
« on: May 07, 2019, 03:54:11 PM »
A bit north of Toronto Ontario. Rob doesn,t have one, I phoned, the original did not have one I think, but the replacement did. I still have the original, the replacement quit last fall.

General Discussion / Re: Bendix change
« on: May 07, 2019, 03:30:43 PM »
I was woundering if anyone know if I can get the washer that goes behind the Bendix. I took it out now if vanished. On utube dangermouse said to be careful not to loose it or something to that effect, too funny. anyway my dealer said I can only get it with a new Bendix. if I could get the thickness maybe I can look around. Anyone up north of border have a extra? just asking

General Discussion / Re: 2020
« on: March 21, 2019, 09:13:58 AM »
I could have  used a kick starter. last fall . I was doing  a enduro and bike stalled out over a log crossing. Bendixwould not engage. I managed to push it fast enough in single tract to bump start it and rode out of test.  It did not lose me the race but certainly cut my day short.That was 2nd bendix. too old and out of shape to be pushing bikes.

Classifieds / 2016 ser 300
« on: August 04, 2018, 01:53:09 PM »
selling 2016 ser 300. Michelin s12 tire heavy tubes, 1900 km. very clean, always stored inside house, never powerwashed, cleaned after every ride. standard fmf exhaust, comes with box of sherco goodies, signals, relay, tool fanny pack. spare rear tire, asking $7000.00 Chris. located southern Ontario canada

General Discussion / Re: Deposit down!
« on: July 15, 2018, 05:32:09 PM »
late September . wow that a bit of a wait

Pages: [1] 2 3 ... 5