Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Trailrider383

Pages: [1] 2 3 4
1
Sherco Tech / Re: 450 Factory stuttering at low load
« on: October 29, 2020, 05:31:02 PM »
Water in the gas maybe? Dump it and try new gas.

2
General Discussion / Re: Analyzing what makes Cody Webb so damn good.
« on: October 24, 2020, 07:04:51 PM »
I see he is riding the 300 SEF Factory in the endurocross series starting next weekend. It will be interesting to see how he does against the 350's and 450's in that class.

He didn't finish first either night. I think they need to put a big bore on the 300. Who knows, maybe they already have.

3
General Discussion / Re: Analyzing what makes Cody Webb so damn good.
« on: October 16, 2020, 07:42:15 PM »
I see he is riding the 300 SEF Factory in the endurocross series starting next weekend. It will be interesting to see how he does against the 350's and 450's in that class.

4
This is what I invented to test.  A tiny fuel filter. I will see if it flows enough air to vent properly.

It didn't solve the problem. The fuel boils just like the stock check valve setup did. It runs fine but somehow fuel still gets through the felt filter I added and drips on the front fender. New idea: I took the front fender off and put air filter foam up into the steering stem hole. Maybe that will catch the fuel before it drips onto the fender.




5
This is what I invented to test.  A tiny fuel filter. I will see if it flows enough air to vent properly.



6
Took out the check valve...problem solved.  Rode in 90 degree heat the other day in slow technical wooded and  sandy conditions and if ever the bike was hot it was then.  No seepage down my front fender.

I removed the check valve on my 2020 300 SEF Factory and it solved the fuel boiling noise but it made the fender staining problem worse!

7
Don't you have an 1 1/8 socket?  Only .023 bigger than 28 mm.

8
General Discussion / Re: 2020 sef 300 factory suspension
« on: June 10, 2020, 06:38:37 AM »
Also if you can't find the suspension info in the manual for the KYB suspension, you will find it in the French section. Clicker settings for comfort, standard and sport. The spring rate for your weight info is in there also.

9
General Discussion / Re: 2020 sef 300 factory suspension
« on: June 08, 2020, 07:13:04 PM »
The suspension on my 2020 300 SEF Factory didn't break in until 20 plus hours.  It is a lot plusher now. Idaho rider also.

10
Sherco Tech / Re: Leaking water cooling from a hole ....
« on: May 18, 2020, 05:33:34 PM »
That is a weep hole for the water pump.

 The weep hole lies between two seals - one that keeps motor oil from the water pump (the oil side water pump seal) and the other to keep coolant in the pump. When the coolant side seal fails fluid drips from the weep hole and eventually leaks out the cover.

https://www.motosport.com/blog/bad-water-pump-symptoms-on-a-dirt-bike-or-atv

11
Classifieds / Re: 2019 300 SEF-R $6900
« on: May 04, 2020, 07:21:41 PM »
Ok, what are you buying next?
You might want to mention where in the world you reside.

12
Sherco Tech / Re: 2019 Sherco SEF 250 high idle, rpms.
« on: April 24, 2020, 09:39:14 PM »
Yeah, my 2020 300 SEF Factory does some weird things after shutting it off for a bit also. No idea what causes it.

13
General Discussion / Re: 2020 KYB's low on oil...
« on: April 23, 2020, 07:33:45 AM »
My 2020 300 SEF Factory had 300 cc in each leg. I put the amount specified from the manual back in. 345 cc. They work great with the heavier springs I put in.


14
Did you find a fix for this? I went to the garage and found the fan running on my 2019 300 SEF. Started it for a minute and shut it off and the fan turned off. Only happened this one time that I know of...

It was trying to tell you that you should have taken it for a ride today with us!  8)

15
Sherco Tech / Re: 2020 300SEF KYB spring rate
« on: April 02, 2020, 04:51:26 PM »
Sounds good. Possibly later next week.

Pages: [1] 2 3 4